bumps with lowered altitude!! (lots of great custom bumps!!)

[td]

yea, running them staggard helps hide the wider front track width, plus it just looks cool!! i get more comments on the 10'' wheels on the back than any other aspect of the truck.

[427blackpearl]

yours being 20'' helps to run the 8'' wide wheel
i dont thik i can run the 8'' wheel in the front and them being 15''???

[td]

if i was running 15's id use 7''s on the front to.

[390F100]

I bet nobody can top my bump with "lowered attitude" [/img]

[td]

Dang!! now thats what you call lay'in frame!

[Randy Beck]

Before lowering,


Shot with DSC-H5 at 2006-10-16


After Lowering


Shot with DSC-H5 at 2006-11-01


Shot with DSC-H5 at 2006-10-15


Shot with DSC-H5 at 2006-10-15

[td]

hey Randy,


ive seen your truck before but never ran into you on the site .
that f-100 you got will scat prety good won't it. i saw one of your u-tube vids a while back, it looked fast . what powerplant you running.



hey brad randy's truck looks like pearls sister

[427blackpearl]

if it had red wheels, i would say it looks familiar to me
looks nice whats the wheel and tire size

td
it looks like pearls sister good for the camera too

[Randy Beck]

hey Randy,


ive seen your truck before but never ran into you on the site .
that f-100 you got will scat prety good won't it. i saw one of your u-tube vids a while back, it looked fast . what powerplant you running.



hey brad randy's truck looks like pearls sister

It has a warmed up 351W bored .030 over with a set of Proline Cyclone heads. Torquer intake, 780 Holley, Comp Cam vavle train. Had it on a chassis dyno a couple of years ago and It made 311hp at the rear wheels. The guy running the dyno said that the motor has around 415- 425hp at the flywheel. He said that I am losing about 100hp thru the drive line.
I have 3 vids on youtube
It runs 8.60 - 8.80's in the 1/8th most of the time. It has ran an 8.55 sec 1/8th mile.


Shot with DSC-H5 at 2008-04-06

[Randy Beck]

if it had red wheels, i would say it looks familiar to me
looks nice whats the wheel and tire size

td
it looks like pearls sister good for the camera too

It has 6" wheels up front with 235/75/15's and 10" wheels on the back with 275/65/15 BFG Comp T/A's

I want to get rid of the steel wagon wheels and get a set of aluminum wheels. I like the Weld draglites and Dragstars but they don't make them with 5.5' lug pattern. At least their website doesn't show them with 5.5"

[Joshpow]

I like the 7 front and 10 rear setup with 15's. That's what the orange truck has. Take a look at my webpage to see how they look.

[Randy Beck]

http://www.youtube.com/my_videos#

The vid with the cobra Mustang, we were side by side all the way down the track untill he hit 3rd gear just before the finish line and he pulled ahead by 1/2 a car length. He had a better E/T but my MPH was faster than his.

[Randy Beck]

Joshpow, Where are you located at in Va.?
I work for NS railroad and I'm in Roanoke quit a bit. The RR puts us up in the Quality Inn near the Roanoke airport.

[ezernut9mm]

my fronts are 7.5 with no issues.

[td]

if it had red wheels, i would say it looks familiar to me
looks nice whats the wheel and tire size

td
it looks like pearls sister good for the camera too

It has 6" wheels up front with 235/75/15's and 10" wheels on the back with 275/65/15 BFG Comp T/A's

I want to get rid of the steel wagon wheels and get a set of aluminum wheels. I like the Weld draglites and Dragstars but they don't make them with 5.5' lug pattern. At least their website doesn't show them with 5.5"

yea randy it bites that you can't get a decent set of race wheels in 5x5.5, i looked a while back myself with no luck.